Asko T700 Operations Instructions download pdf (Page 12)

Page 12

Connecting a Four-wire Power Cord

Connecting a Three-wire Power Cord

ELECTRICAL CONNECTIONSELECTRICAL CONNECTIONS

The power supply cord must be grounded. If the

machine is to be used in a wet area, the supply must

be protected by a residual current device.

CAUTION:

The receptacle on the rear of the machine is designed

to accommodate ASKO washers ONLY (rated 208–

240 V.) To use this receptacle, you must use the ready-

fitted plug supplied with the washing machine or an

equivalent. The supply connection must be 208–240 V,

20 A.

ASKO washers rated 208–240 V have two internal

fuses of 15 A each.

Remove cover to

access terminal box.

(Requires a 20-Torx

screwdriver.)

WARNING! Before starting this procedure, be sure

the power is turned off at the breaker/fuse box.

WARNING! Before starting this procedure, be sure

the power is turned off at the breaker/fuse box.

1. Turn the power off at the breaker/fuse box.

2. Remove terminal block cover.

3. Use the strain relief attached below the terminal

block opening.

4. Loosen or remove center terminal block screw.

5. Connect neutral wire

(white ) of power

supply cord to the

center, silver-colored

terminal screw.

Tighten screw.

6. Connect the other

wires to outer screws.

7. Tighten the strain

relief screws.

8. Replace terminal box

cover on back of dryer.

9. Plug dryer into wall

receptacle.

10. Turn power on at

breaker/fuse box.

Power Supply Cord

You will need a three-wire power supply cord with three

No. 10 copper wires and a matching three-wire

receptacle of NEMA Type 10-30R, as illustrated below:

1. Turn the power off at the breaker/fuse box.

2. Remove terminal block cover.

3. Use the strain relief attached below the terminal

block opening.

4. Remove center terminal block screw.

5. Remove ground wire

(green with yellow stripes)

from external ground

connector screw. Fasten

under center, silver-

colored terminal block

screw.

6. Connect ground wire

(green) of cord to external

ground conductor screw.

7. Connect neutral wire (white)

of cord under center screw

of terminal block.

8. Connect the other wires

to outer screws.

9. Tighten the strain relief screws.

10. Replace terminal box cover on back of dryer.

11. Plug dryer into wall receptacle.

12. Turn power on at breaker/fuse box.

Spade terminals

with upturned

ends

FOUR-WIRE CORD

Neutral

Ground

prong

Ring

terminals

Neutral

(white)

Ground

(green)

3/4” UL-listed

strain relief

Power Supply Cord

You will need a four-wire power supply cord with four

No. 10 copper wires and a matching four-wire

receptacle of NEMA Type 14-30R, as illustrated below.

The fourth wire must be identified with a green cover

and the neutral conductor by a white cover.

NOTE: In Canada, the dryer is delivered ready-fitted with

a four-prong plug intended for connection to a single-

phase supply.

Connection to a permanently wired supply point must

be made only by a qualified electrician.

As supplied: Single-phase, 230 V, 60 Hz,

2500 Watt heater rating

30 A fuse required

THREE-WIRE CORD

Spade terminals

with upturned

ends

Ring

terminals

This blade connects

to this conductor.

Neutral

3/4” UL-listed

strain relief

Neutral

(white)

1 2 ... 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Asko T700 Operations Instructions Page 12

Comments to this Manuals

Related products and manuals for Washing machines Asko T700